BETCO XT3 21 Návod k obsluze

XT3XT3 221121Battery BurnisherE12601-00Operators ManualParts Schematic©2007 Betco Corporation. All Rights Reserved. 1001 Brown Avenue  Toledo,

ADD DISTILLED WATER, AS NEEDED, SO THAT ELECTROLYTE LEVEL IS ABOUT 1/2" ABOVE PLATES.DO NOT OVERFILL.DO NOT FILL ABOVE THE BOTTOM OF THE TUBETHAT

BATTERY CHARGER OPERATION OPERATION • PLUG THE CORD FROM THE CHARGER INTO A 110 VOLT OUTLET • Batteries should now start charging. • A test is r

HOW TO SET THE CHARGER FOR DIFFERENT SIZES AND TYPES OF BATTERIES UP IS ON DOWN IS OFF DIP 1, DIP 2, DIP 3, AND DIP 4 ARE FOR SELECTING THE CHARGI

BDI DISPLAY When the machine is turned on, the battery level indicator is switched on and the LED (D or E) corresponding to the position currently hel

ADETAIL A SCALE 1 : 6TILT MACHINE BACK ANDREMOVE FRONT COVERUSE 3/4" OPEN ENDWRENCH TO SECURESHAFT AND SPINPAD DRIVER OFFSHAFT BY HANDPAD CHANGIN

BALANCING INSTRUCTIONSFor best operation and maximum battery life, the XTG3 battery burnisher must have thecorrect pad pressure. The burnisher should

LOCATIONOF SERIAL # SERIAL NUMBER LOCATION ANDSHIPPING EYEBOLT REPLACEMENTHAVE SERIAL NUMBER AVAILABLE WHEN CALLING SERVICE CENTERFOR PARTS OR SERVICE

XT3-21 BELT TENSIONING INSTRUCTIONSTO TIGHTEN THE BELT TENSIONER (Tensioner may have slipped, or belt may have stretched)Tilt machine back and remove

141516111333256711416548ITEM NO.PART NO.QTY.DESCRIPTION1E012653121" DURACOAT MILLED DECK2E0126333LATCH, RUBBER DRAW (PART 1 OF 2)3E0126251ROTOMOL

A121415161113ITEM NO.PART NO.QTY.DESCRIPTION1E012653121" DURACOAT MILLED DECK2E0126333LATCH, RUBBER DRAW (PART 1 OF 2)3E0126251ROTOMOLDED SHROUD

411139811131489893XT3-21 DECK, FRAME, AND WHEELS65771224ITEM NO.PART NO.QTY.DESCRIPTION1E0107051BUMPER GUARD, RED2E0115315RIVET, T-RIVET, BSP T633E012

A20181912171021123151611ITEM NO.PART NO.QTY.DESCRIPTION1E0107051BUMPER GUARD, RED2E0115315RIVET, T-RIVET, BSP T633E012653121" DURACOAT MILLED DEC

A12131710101820151931489107161ITEM NO.PART NO.QTY.DESCRIPTION1E012653121" DURACOAT MILLED DECK2*4SHIM FOR FRONT END BEARING HOUSING3E0122841BEARI

1646511131231XT3-21 MOTOR, PULLEYS, AND BELTITEM NO.PART NO.QTY.DESCRIPTION1E012653121" DURACOAT MILLED DECK2*4SHIM FOR FRONT END BEARING HOUSING

25834671XT3-21 FLEX-LOC PAD DRIVER ASSEMBLY(COMPLETE ASSEMBLY- PE50028)ITEM NO.PART NO.QTY.DESCRIPTION1E0102501FLEX-LOC 21 2E0105861SHAFT TO PAD DRIVE

72706971597668949593909189635XT3-21 ELECTRICAL AND BATTERY VIEW2829606162627529646662986WIRING HARNESS(CONTROLLER TO MOTORAND ELECTRICAL PARTS)6773835

ITEM NO.PART NO.QTY.DESCRIPTION5E0126431CHARGER CORD WRAP6E0118332SCREW, 1/4-20 x .75, PHMS, BLACK28E01183416WASHER, FLAT, 1/429E01221917SCREW, 1/4-20

88879292848139778280797995837878ITEM NO.PART NO.QTY.DESCRIPTION1E0107051BUMPER GUARD, RED2E0115315RIVET, T-RIVET, BSP T633E012653121" DURACOAT MI

ELECTRICAL LAYOUTE012215SAFETY SWITCHE012629KEYSWITCHE012646LAMPE012630BDI (REAR OF BDI)E011529ROCKER SWITCHE012592SOLENOIDE012628CHARGERE012197MOTORX

1381217181920M1M2M3B+B-123458BLACKBLUEGREENWHITEREDUVWWIRING LADDER DIAGRAMMOTORMOTORCONTROLBDI+-+-CHARGERcLEDACKKEYK - KEY SWITCHR - ROCKER SWITCHS -

TABLE OF CONTENTS COVER PAGE 1 LEFT BLANK INTENTIONALLY 2 TABLE OF CONTENTS 3 SAFETY INSTRUCTIONS 4 - 5 SPECIFICATIONS 6 PROCEDURES FOR LOADING,

1234567883112171819201217181920FFFFMMMMWIRING HARNESS123NOTE - MOLEX CONNECTORS VIEWED FROM WIRE SIDE1 - MOLEX 39-01-2200 TO CONTROL2 - MOLE

TROUBLE-SHOOTING PROBLEM CAUSE POSSIBLE SOLUTION No sign of power. No on lamp, no BDI readout. (a) Bad connection (b) Bad connection to BDI (c) On

©2006 Betco Corporation All Rights Reserved. 1001 Brown Avenue Toledo, Ohio 43607-0127 888-462-3826 www.betco.com BBeettccoo WWaarrrraannttyy EExx

SAFETY INSTRUCTIONS Hazard Level Explanation or Description of Hazard Level Failure to follow safety instructions labeled could result in sever

SAFETY INSTRUCTIONS Battery acid is dangerous. Wear eye and face protection, hand protection, and body protection when working on and around batterie

XT3 - 21 Product Specifications Burnish path: 21” Pad size: 21” Motor: Maintenance Free, brushless, rated at 5 hp. Motor controller: Mo

Procedures for Loading, Transporting, and Unloading Battery Burnisher The machine is very heavy, so be very careful when loading, transporting, an

KEY SWITCHROCKER SWITCHSAFETY LEVEROPERATING INSTRUCTIONSTO START BUFFING:# 1 - TURN ON KEY SWITCH# 2 - TURN ON ROCKER SWITCH# 3 - DEPRESS SAFETY HAND

BATTERY CHARGINGREFER TO NEXT THREE PAGES FOR BATTERY CHARGER OPERATIONAND BATTERY MAINTENANCEBecome familiar with and follow the instructions issued